问题描述:
请问ws5800恢复出厂设置的命令是什么,没有rest save-configrition这条命令。
组网及组网描述:
9小时前提问
在<>模式下使用
reset saved-configuration
9小时前回答暂无
删除dir目录下的cfg文件mdb文件,然后不保存配置重启即可
8小时前回答暂无
<>
reset sa
n
y
8小时前回答暂无
您好,请知:
以下是恢复出厂设置的方法:
方法一:
<H3C>reset saved-configuration //清空交换机配置
The saved configuration file will be erased. Are you sure? [Y/N]:y //设备提示保存的配置将会被删除,是否继续。
Configuration file in flash: is being cleared. Please wait ...
MainBoard:
Configuration file is cleared. //配置已被清空
<H3C>reboot //重启交换机
Start to check configuration with next startup configuration file, please wait.........DONE!
Current configuration may be lost after the reboot, save current configuration? [Y/N]:n //设备提示会在重启后丢失当前配置,是否保存当前配置,选择n
This command will reboot the device. Continue? [Y/N]:y //设备提示设备将会重启,是否继续,选择Y
Now rebooting, please wait...
%Dec 14
方法二:
<H3C>dir //通过dir命令查看交换机的文件
Directory of flash:
0 drw- - Dec 14
1 -rw- 1554 Dec 14
2 -rw-
3 drw- - Dec 14
4 -rw-
5 drw- - Dec 14
6 -rw- 0 Dec 14
7 -rw- 0 Dec 14
8 drw- - Dec 14
9 -rw- 6118 Dec 14
10 -rw- 110464 Dec 14
1046512 KB total (1046300 KB free)
<H3C>delete startup.cfg //使用删除命令删除startup.cfg这个启动运行的配置文件
Delete flash:/startup.cfg? [Y/N]:y //设备提示是否要删除,选择Y
Deleting file flash:/startup.cfg... Done. //设备提示startup.cfg这个文件已删除完成
<H3C>reboot //重启交换机
Start to check configuration with next startup configuration file, please wait.........DONE!
Current configuration may be lost after the reboot, save current configuration? [Y/N]:n //设备提示会在重启后丢失当前配置,是否保存当前配置,选择n
This command will reboot the device. Continue? [Y/N]:y //设备提示设备将会重启,是否继续,选择Y
Now rebooting, please wait...
8小时前回答暂无
你正在,Ws5800恢复出厂设置当傻瓜用。
版权声明:本文内容源于互联网搬运整理,仅限于小范围内传播学习和文献参考,不代表本站观点,请在下载后24小时内删除,如果有侵权之处请第一时间联系我们删除。敬请谅解! E-mail:c#seox.cn(#修改为@)
CRM论坛:CRM论坛(CRMBBS.COM)始办于2019年,是致力于✅CRM实施方案✅免费CRM软件✅SCRM系统✅客户管理系统的垂直内容社区网站,CRM论坛持续专注于CRM领域,在不断深化理解CRM系统的同时,进一步利用新型互联网技术,为用户实现企业、客户、合作伙伴与产品之间的无缝连接与交互。