SecPath F1060 配置context分配接口报错

问题描述：

两台F1060做了IRF2，之后配置Context。在给Context分配接口时，可以选择独占方式分配（不带share参数）、共享方式分配（带share参数），但是选择独占方式时，分配端口会报错：Group error: all interfaces of one group must be allocated to the same mdc.与手册描述不符，请问是什么原因？

(4)

最佳答案

确认是在防火墙配置的？防火墙是context命令，不是mdc。

[F5020]mdc 1
       ^
 % Unrecognized command found at '^' position.
[F5020]context 1

[F5020-context-5-1]allocate interface GigabitEthernet 1/0/?
  <0-22>  GigabitEthernet interface number

[F5020-context-5-1]allocate interface GigabitEthernet 1/0/22
Configuration of the interfaces will be lost. Continue? [Y/N]:y
GigabitEthernet1/0/22 has been allocated in sharing mode. Please cancel the allocation in sharing mode first.

[F5020-context-5-1]allocate interface g1/0/22 share
[F5020-context-5-1]

[F5020-context-5-1]allocate interface GigabitEthernet 1/0/19
Configuration of the interfaces will be lost. Continue? [Y/N]:y

[F5020-context-5-1]

(4)

·     对于本系列交换机，一块业务板上的所有接口只能加入一个MDC。因此为某个MDC分配接口时，请将一块业务板上的所有接口分配给该MDC。

# 将接口FortyGigE1/0/1分配给MDC sub1。

<Sysname> system-view

[Sysname] mdc sub1

[Sysname-mdc-2-sub1] allocate interface fortygige 1/0/1

Configuration of the interfaces will be lost. Continue? [Y/N]:y

Group error: all interfaces of one group must be allocated to the same mdc.

  FortyGigE1/0/1

Port list of group 4:                                                          

  FortyGigE1/0/1           FortyGigE1/0/2                  

  FortyGigE1/0/3           FortyGigE1/0/4                  

  FortyGigE1/0/5           FortyGigE1/0/6                  

  FortyGigE1/0/7           FortyGigE1/0/8                  

以上提示信息表明必须将接口FortyGigE1/0/1～FortyGigE1/0/8一起分配给同一个MDC。执行如下命令，将接口FortyGigE1/0/1～FortyGigE1/0/8一起分配给MDC sub1：

[Sysname-mdc-2-sub1] allocate interface fortygige 1/0/1 to fortygige 1/0/8

Configuration of the interfaces will be lost. Continue? [Y/N]:y

所以应该是出于系统硬件或者版本的限制导致，建议更换设备测试一下！

(1)

华三官网的资料都是经过物理设备，真机验证过后得到的结果，一般不会出现测试结果不一致的问题。建议注意核对设备版本和配置方法的差异。

(1)

[H3C-context-10-con10]allocate interface GigabitEthernet 1/0/11 Configuration of the interfaces will be lost. Continue? [Y/N]:y Group error: all interfaces of one group must be allocated to the same mdc. GigabitEthernet1/0/11 Port list of group 1: GigabitEthernet1/0/0 GigabitEthernet1/0/1 GigabitEthernet1/0/2 GigabitEthernet1/0/3 GigabitEthernet1/0/4 GigabitEthernet1/0/5 GigabitEthernet1/0/6 GigabitEthernet1/0/7 GigabitEthernet1/0/8 GigabitEthernet1/0/9 GigabitEthernet1/0/10 GigabitEthernet1/0/11