44094,MSR26-00如何配置IP和OSPF
问题描述：
图一 图二为配置参考
组网及组网描述：
以上图1 图2是参考文件 图三是 给我们的IP地址和 OSPF地址
以下是目前 MSR 26-00的配置 请问要怎么改
<H3C>dis cu # version 5.20, Release 2514P14 # sysname H3C # domain default enable system # dns proxy enable # telnet server enable # dar p2p signature-file flash:/p2p_default.mtd # ndp enable # ntdp enable # cluster enable # port-security enable # password-recovery enable # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable # dhcp server ip-pool vlan1 extended network ip range 192.168.1.2 192.168.1.254 network mask 255.255.255.0 gateway-list 192.168.1.1 dns-list 192.168.1.1 # user-group system group-attribute allow-guest # local-user admin password cipher $c$3$40gC1cxf/wIJNa1ufFPJsjKAof+QP5aV authorization-attribute level 3 service-type telnet service-type web # cwmp undo cwmp enable # interface Aux0 async mode flow link-protocol ppp # interface Cellular0/0 async mode protocol link-protocol ppp tcp mss 1024 # interface NULL0 # interface Vlan-interface1 ip address 192.168.1.1 255.255.255.0 tcp mss 1024 dhcp server apply ip-pool vlan1 # interface GigabitEthernet0/0 port link-mode route tcp mss 1024 # interface GigabitEthernet0/1 port link-mode route tcp mss 1024 # interface GigabitEthernet0/2 port link-mode bridge # interface GigabitEthernet0/3 port link-mode bridge # interface GigabitEthernet0/4 port link-mode bridge # interface GigabitEthernet0/5 port link-mode bridge # interface GigabitEthernet0/6 port link-mode bridge # interface GigabitEthernet0/7 port link-mode bridge # interface GigabitEthernet0/8 ---- More ---- #Jan 1 00:06:15:884
最佳答案
两台都是V5平台的设备，配置上是一样的，只是接口号要换一下，还有把接口下的IP换成你需要改成的IP地址，其他东西都不需要边，命令也都没有变化。
#
interface Ethernet0/0 //换成GigabitEthernet 0/0
port link-mode route
ip address 182.16.100.
#
interface Ethernet0/1 //换成GigabitEthernet 0/1
port link-mode route
ip address 17.169.100.102 255.255.255.252 //换成对应的地址
#
interface NULL0
#
OSPF 1
area 0.0.0.12 //看你之前MSR20配置，是区域51，但是给出的IP规划是区域12，根据你实际的情况配置
network 182.16.100.200 0.0.0.7 //把G0/0和G0/1的地址发布进来就可以了
network 17.169.100.100 0.0.0.3
你这个配置看着太乱了
16.169.105.25和 16.169.105.26应该是分别配置两台路由器三层接口上的，并且需要在ospf areas 12里面通告该网段的路由。
172.160.110.49到 172.160.110.54应该是内网地址段，可以配置DHCP。
关于这款设备ospf配置可以参考：
http://www.h3c.com/cn/d_
这是之前MSR20-20的配置 现在是设备和地址都换了 换成新的了 不会配置
# version 5.20, Release 2311, Basic
# sysname H3C
# domain default enable system
# dns proxy enable
# telnet server enable
# dar p2p signature-file cfa0:/p2p_default.mtd
# port-security enable
# vlan 1
# domain system access-limit disable state active idle-cut disable self-service-url disable
# user-group system group-attribute allow-guest
# local-user admin password cipher $c$3$bWCdFR5k16955j8YqDhV8CQbWoeDt20k authorization-attribute level 3 service-type telnet service-type web
# interface Aux0 async mode flow link-protocol ppp
# interface Cellular0/0 async mode protocol link-protocol ppp
# interface Ethernet0/0 port link-mode route ip address 182.16.100.
# interface Ethernet0/1 port link-mode route ip address 17.169.100.102 255.255.255.252
# interface NULL0 # ospf 1 area 0.0.0.51 network 182.16.100.200 0.0.0.7 network 17.169.100.100 0.0.0.3
# ip route-static 0.0.0.0 0.0.0.0 Ethernet0/1 17.169.100.101
# load xml-configuration # user-interface con 0 user-interface tty 13 user-interface aux 0 user-interface vty 0 4 authentication-mode scheme
# return
那你直接在路由器连接外网的接口上配置ip地址16.169.105.26 [h3c]int g0/0 [h3c-int g0/0]ip add 16.169.105.26 (假如你的外网口是g0/0) 然后保证对端地址也正常配置
James 发表时间：你是说用WEB配吗
zhiliao_44094 发表时间：以前是你们工程师通过邮件 写了命令发给我 然后我在路由器上运行
zhiliao_44094 发表时间：我给你个参考文件 我再发一下
zhiliao_44094 发表时间：# version 5.20, Release 2311, Basic # sysname H3C # domain default enable system # dns proxy enable # telnet server enable # dar p2p signature-file cfa0:/p2p_default.mtd # port-security enable # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher $c$3$bWCdFR5k16955j8YqDhV8CQbWoeDt20k authorization-attribute level 3 service-type telnet service-type web # interface Aux0 async mode flow link-protocol ppp # interface Cellular0/0 async mode protocol link-protocol ppp # interface Ethernet0/0 port link-mode route ip address 182.16.100.241 255.255.255.248 # interface Ethernet0/1 port link-mode route ip address 17.169.100.122 255.255.255.252 # interface NULL0 # ospf 1 area 0.0.0.51 network 17.169.100.120 0.0.0.3 network 182.16.100.240 0.0.0.7 # ip route-static 0.0.0.0 0.0.0.0 Ethernet0/1 17.169.100.121 # load xml-configuration # user-interface con 0 user-interface tty 13 user-interface aux 0 user-interface vty 0 4 authentication-mode scheme # return
zhiliao_44094 发表时间：ospf area 51 医保中心广域网IP TO 医院（药店）端广域网IP /30 17.169.100.121 TO 17.169.100.122 255.255.255.252 医院(药店)端路由器IP TO 医院端前置机IP /29 182.16.100.241 TO 182.16.100.246 255.255.255.248
zhiliao_44094 发表时间：你看看我要怎么改 MSR20-20 和 MSR26-00好像接口不一样的 我单改IP传上去没用
zhiliao_44094 发表时间：我看Ethernet0/0 和 Ethernet0/1都是三层口，不知道那个是连接外网的 直接 [h3c]int e 0/0 [h3c-int e 0/0 ]ip add x.x.x.x x.x.x.x
James 发表时间：MSR26-00 OSPF怎么添加
zhiliao_44094 发表时间：
