闫卫双,H3C S7506E-S telnet密码和console密码被锁死,请教下如何恢复,在线等..
问题描述:
设备信息和ctrl+B 菜单如下图,请教怎么跳过当前配置启动交换机
最佳答案
console密码忘记可以参考如下
方法一:
1. 进入BootWare菜单
(1) 设备上电和重新启动的过程中,在配置终端的屏幕上首先将显示
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU...
Press Ctrl+T to start heavy memory test
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.....Done.
****************************************************************************
* *
* H3C F1020 BootWare, Version 1.04 *
* *
****************************************************************************
Compiled Date : Sep 10
CPU Type : xlp208
CPU Clock Speed : 1000MHz
Memory Type : DDR3 SDRAM
Memory Size : 2048MB
Memory Speed : 1332MHz
BootWare Size : 768KB
Flash Size : 8MB
CPLDA Version : 2.0
CPLDB Version : 2.0
PCB Version : Ver.A
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
(2) 当出现“Press Ctrl+B to enter extended boot menu...”时,立即键入<Ctrl+B>,按下<Enter>键后,系统将进入BootWare主菜单。
在显示信息中可以查看是否使能密码恢复功能。
表8 显示信息描述表
显示信息
说明
Password recovery capability is enabled.
密码恢复功能处于开启状态
Password recovery capability is disabled.
密码恢复功能处于关闭状态
Password recovery capability is disabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
如果提示Password recovery capability is enabled.则可以按8,跳过console密码,直接进入命令行,该种方法可跳过console密码直接进入命令行
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
表9 BootWare主菜单
菜单项
说明
<1> Boot System
引导启动文件
<2> Enter Serial SubMenu
进入串口子菜单。子菜单详细描述请参见表12
<3> Enter Ethernet SubMenu
进入以太网口子菜单。子菜单详细描述请参见表10
<4> File Control
文件控制子菜单。子菜单详细描述请参见表16
<5> Restore to Factory Default Configuration
恢复到出厂配置状态
· 该功能仅在密码恢复功能处于关闭状态下执行有效
· 执行该功能后,系统将删除用户当前使用的配置文件,并且以空配置启动。请谨慎使用该功能
<6> Skip Current System Configuration
跳过当前配置进行启动,只是本次生效。该功能一般在用户丢失口令之后使用
该功能仅在密码恢复功能处于开启状态下执行有效
<7> BootWare Operation Menu
BootWare操作子菜单,用于BootWare程序操作
<8> Skip Authentication for Console Login
跳过Console口认证登录进行启动,只是本次生效。该功能一般在丢失Console口口令之后使用
该功能仅在密码恢复功能处于开启状态下执行有效
<9> Storage Device Operation
存储设备控制菜单,用于存储设备的选择
<0> Reboot
重新启动设备
方法二:
1. 进入BootWare菜单
(1) 设备上电和重新启动的过程中,在配置终端的屏幕上首先将显示
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU...
Press Ctrl+T to start heavy memory test
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.....Done.
****************************************************************************
* *
* H3C F1020 BootWare, Version 1.04 *
* *
****************************************************************************
Compiled Date : Sep 10
CPU Type : xlp208
CPU Clock Speed : 1000MHz
Memory Type : DDR3 SDRAM
Memory Size : 2048MB
Memory Speed : 1332MHz
BootWare Size : 768KB
Flash Size : 8MB
CPLDA Version : 2.0
CPLDB Version : 2.0
PCB Version : Ver.A
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
(2) 当出现“Press Ctrl+B to enter extended boot menu...”时,立即键入<Ctrl+B>,按下<Enter>键后,系统将进入BootWare主菜单。
在显示信息中可以查看是否使能密码恢复功能。
表8 显示信息描述表
显示信息
说明
Password recovery capability is enabled.
密码恢复功能处于开启状态
Password recovery capability is disabled.
密码恢复功能处于关闭状态
Password recovery capability is disabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
===========================<EXTEND-BOOTWARE MENU>===========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
表9 BootWare主菜单
菜单项
说明
<1> Boot System
引导启动文件
<2> Enter Serial SubMenu
进入串口子菜单。子菜单详细描述请参见表12
<3> Enter Ethernet SubMenu
进入以太网口子菜单。子菜单详细描述请参见表10
<4> File Control
文件控制子菜单。子菜单详细描述请参见表16
<5> Restore to Factory Default Configuration
恢复到出厂配置状态
· 该功能仅在密码恢复功能处于关闭状态下执行有效
· 执行该功能后,系统将删除用户当前使用的配置文件,并且以空配置启
另外,看该bootrom没有跳过console密码选项,如果需要清空该密码,可以在文件选项中尝试删除掉配置文件,不过这种方法配置文件会丢失
li 发表时间:该问题暂时没有网友解答